Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung
Vorhergehende Überarbeitung
Nächste ÜberarbeitungBeide Seiten der Revision
embedded_systems:imx6:db [2017-05-03 12:07] grafembedded_systems:imx6:db [2020-06-12 17:07] graf
Zeile 1: Zeile 1:
-====== Drive Board der NTB ======+====== Drive Board of the NTB ======
 ===== db11 Board ===== ===== db11 Board =====
 <box 30% right green| **Features**> <box 30% right green| **Features**>
Zeile 5: Zeile 5:
 </box> </box>
  
-  * {{:embedded_systems:imx6:db11schematic.pdf|Schema}} +  * {{:embedded_systems:imx6:db11schematic.pdf|Schematics}} 
-  * Repository auf Github mit Altium Files https://github.com/ntb-ch/db11 +  * Repository on github with Altium files https://github.com/ntb-ch/db11 
-  * AchtungVerbindungen zu cb20 kurz haltenDifferentielle Line Driver für Encoder befinden sich auf dem db11. Von hier gehen single-ended Leitungen zum cb20. +  * Importantkeep connections to cb20 reasonably shortDefferential line drivers for the encoders are located on the db11. From there single ended lines lead to the cb20. 
-  * Achtung: Power Gnd der ESCON Module mit Gnd verbinden.+<box 30% right blue| **existing boards**> 
 +  * 6 x db11 2015 (incl. production in 2017) 
 +</box> 
 + 
 +===== Supply ===== 
 +The board is supplied with 5V and 3.3V directly from the cb20, see below. On P6 you have to deliver 24V (square pad = Gnd).\\  
 +Important: Connect GND of P6 with GND of the cb20. 
 + 
 +===== Motor Connection ===== 
 +A simple DC-Motor (single coil) must be connected on P5(Pin 1 and 2).
  
-===== Verbindungen zum cb20 Board ===== +===== Connections to the cb20 Board ===== 
-Die folgenden Verbindungen müssen für die Ansteuerung aller vier Drives gemacht werden:+Connect the following lines when using all 4 drives:
 |      ^cb20      ^^db11      ^^ |      ^cb20      ^^db11      ^^
-|Signal|Stecker|Pin|Stecker|Pin| +|Signal|Connector|Pin|Connector|Pin| 
-|enc1/A|P8     | |P1     |3  |+|3.3V  |P8     | |P1     |25  | 
 +|DGND  |:::    |2  |:::    |2  | 
 +|enc1/A|:::    |3  |:::    |3  |
 |enc1/B|:::    |4  |:::    |4  | |enc1/B|:::    |4  |:::    |4  |
 |enc2/A|:::    |5  |:::    |5  | |enc2/A|:::    |5  |:::    |5  |
Zeile 22: Zeile 33:
 |enc4/A|:::    |9  |:::    |9  | |enc4/A|:::    |9  |:::    |9  |
 |enc4/B|:::    |10 |:::    |10 | |enc4/B|:::    |10 |:::    |10 |
-|enable|P9     |3  |P1     |11 |+|enable|P9     |3  |:::    |11 |
 |ready1|:::    |5  |:::    |12 | |ready1|:::    |5  |:::    |12 |
 |ready2|:::    |6  |:::    |13 | |ready2|:::    |6  |:::    |13 |
 |ready3|:::    |7  |:::    |14 | |ready3|:::    |7  |:::    |14 |
 |ready4|:::    |8  |:::    |15 | |ready4|:::    |8  |:::    |15 |
-|AGND  |P10    |3  |P1     |18 |+|5V    |P10    |1  |:::    |1  | 
 +|AGND  |:::    |3  |:::    |18 |
 |dac1  |:::    |5  |:::    |17 | |dac1  |:::    |5  |:::    |17 |
 |dac2  |:::    |7  |:::    |19 | |dac2  |:::    |7  |:::    |19 |