Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung
Vorhergehende Überarbeitung
Letzte ÜberarbeitungBeide Seiten der Revision
embedded_systems:imx6:db [2017-08-29 12:56] grafembedded_systems:imx6:db [2021-08-26 15:04] Urs Graf
Zeile 1: Zeile 1:
-====== Drive Board der NTB ======+====== Drive Board of the NTB ======
 ===== db11 Board ===== ===== db11 Board =====
 <box 30% right green| **Features**> <box 30% right green| **Features**>
Zeile 5: Zeile 5:
 </box> </box>
  
-  * {{:embedded_systems:imx6:db11schematic.pdf|Schema}} +  * {{:embedded_systems:imx6:db11schematic.pdf|Schematics}} 
-  * Repository auf Github mit Altium Files https://github.com/ntb-ch/db11 +  * Repository on github with Altium files https://github.com/ntb-ch/db11 
-  * AchtungVerbindungen zu cb20 kurz haltenDifferentielle Line Driver für Encoder befinden sich auf dem db11. Von hier gehen single-ended Leitungen zum cb20. +  * Importantkeep connections to cb20 reasonably shortDifferential line drivers for the encoders are located on the db11. From there single ended lines lead to the cb20. 
-<box 30% right blue| **vorhandene Boards**> +<box 30% right blue| **existing boards**> 
-  * 6 x db11 2015 (inklNachproduktion 2017)+  * 6 x db11 2015 (inclproduction in 2017)
 </box> </box>
  
-===== Speisung ===== +===== Supply ===== 
-Die Versorgung mit 5V und 3.3V erfolgt vom cb20 Boardsiehe untenÜber P6 muss das Board mit 24V gespeist werden (eckiger Pad = Gnd).\\  +The board is supplied with 5V and 3.3V directly from the cb20, see belowOn P6 you have to deliver 24V (square pad = Gnd).\\  
-Achtung: GND von P6 mit GND der Speisung des cb20 verbinden.+ImportantConnect GND of P6 with GND of the cb20.
  
-===== Anschluss Motor ===== +===== Motor Connection ===== 
-Ein einfacher DC-Motor (einzelne Wicklungmuss auf P5(Pin 1 und 2) angeschlossen werden.+A simple DC-Motor (single coilmust be connected on P5(Pin 1 and 2).
  
-===== Verbindungen zum cb20 Board ===== +===== Connections to the cb20 Board ===== 
-Die folgenden Verbindungen müssen für die Ansteuerung aller vier Drives gemacht werden:+Connect the following lines when using all 4 drives:
 |      ^cb20      ^^db11      ^^ |      ^cb20      ^^db11      ^^
-|Signal|Stecker|Pin|Stecker|Pin|+|Signal|Connector|Pin|Connector|Pin|
 |3.3V  |P8     |1  |P1     |25  | |3.3V  |P8     |1  |P1     |25  |
 |DGND  |:::    |2  |:::    |2  | |DGND  |:::    |2  |:::    |2  |