Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende ÜberarbeitungNächste ÜberarbeitungBeide Seiten der Revision |
software:linux:toradex:toradex-easy-installer [2020-03-25 11:21] – mlammerich | software:linux:toradex:toradex-easy-installer [2023-07-21 09:32] – Urs Graf |
---|
====== Toradex Easy Installer ====== | ====== Toradex Easy Installer ====== |
| |
The Toradex Easy Installer is Toradex's recommended option for flashing images onto their modules. It can be downloaded from the [[ https://developer.toradex.com/software/toradex-easy-installer#os-and-demo-images | Toradex Wiki ]]. | The Toradex Easy Installer is Toradex's recommended option for flashing images onto their modules. The method described below loads the installer into RAM, boots from there and allows to flash a new image. We were currently not able to boot from our current image into the Toradex Easy Installer sitting on a USB stick, see [[software:linux:toradex:Toradex Easy Installer on USB]]. |
| |
===== Booting into Toradex Easy Installer ===== | |
| |
Download the Toradex Easy Installer from the [[ https://developer.toradex.com/software/toradex-easy-installer#os-and-demo-images | Toradex Wiki ]] and extract the downloaded archive onto a SD Card or USB Stick. Insert the into the Board's SD Card slot or USB port and power it on. | ===== Getting Toradex Easy Installer ===== |
| You need the Colibri evaluation module, see [[embedded_systems:imx6:evm|Colibri Evaluation Board from Toradex]]. Follow instructions on [[https://developer.toradex.com/easy-installer/toradex-easy-installer/loading-toradex-easy-installer|Loading Toradex Easy Installer]] to get the installer and load it via USB OTG into the RAM. First, you have to enter recovery mode, see //Using a command in the bootloader//. If there is no longer any bootloader on the board, follow instructions under //Using hardware mechanism//. Next, load the installer with [[https://developer.toradex.com/easy-installer/toradex-easy-installer/loading-toradex-easy-installer#load-toradex-easy-installer-through-the-usb-otg-interface|these instructions]]. It will now automatically boot into the Toradex Easy Installer. |
| |
Interrupt the boot process (hit any key) to boot into [[ .:uboot | uboot]]. Now run ''run bootcmd_mmc1'' to boot from the SD Card or ''run bootcmd_usb0'' to boot from USB. | |
| |
Note that while Toradex recommends using the ''run_distro_bootcmd'' this will boot from the modules internal flash if a bootable image is present. | |
| |
===== Installing an Image ===== | ===== Installing an Image ===== |
| |
Connect to the module using a remote desktop connection as described on the [[ https://developer.toradex.com/software/toradex-easy-installer#os-and-demo-images | Toradex Wiki ]]. Select the desired image and click install. | You will need a VNC client installed to connect to the installer. |
| For Ubuntu: |
| <code> |
| sudo apt install tigervnc-viewer |
| </code> |
| |
| Then connect to the installer with |
| <code> |
| vncviewer <ip address> |
| </code> |
| |
| The following window should appear: |
| |
| {{:software:linux:toradex:tezi.png?400|}} |
| |
| Now select the desired image and click install. |
| |
| |
| === Images Feeds === |
| |
| Images can be browsed on the [[ software:linux:images:start| Images Page]]. By adding the webserver address provided on the [[ software:linux:images:start| Images Page]] to the feeds, the images can be installed directly over the web. |
| |
=== Image not showing up === | === Image not showing up === |