Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende ÜberarbeitungNächste ÜberarbeitungBeide Seiten der Revision |
software:linux:yocto:cb20 [2023-07-07 13:56] – Urs Graf | software:linux:yocto:cb20 [2023-08-08 13:15] – Urs Graf |
---|
Note that the ''cb20'' machine requires the ''meta-ost-toradex'' layer that is part of [[meta-ost]]. | Note that the ''cb20'' machine requires the ''meta-ost-toradex'' layer that is part of [[meta-ost]]. |
| |
Follow the [[software:linux:yocto:setup|Setup and Building]] guide to set up the build environment and change the machine definition in ''local.conf'' | Follow the [[software:linux:yocto:setup|Setup and Building]] guide to set up the build environment. Fetch board and processor specific repositories: |
| * meta-freescale, https://github.com/Freescale/meta-freescale.git, branch dunfell |
| * meta-freescale-3rdparty, https://github.com/Freescale/meta-freescale-3rdparty.git, branch dunfell |
| * meta-toradex-bsp-common, git://git.toradex.com/meta-toradex-bsp-common.git, branch dunfell-5.x.y |
| * meta-toradex-nxp, git://git.toradex.com/meta-toradex-nxp.git, branch dunfell-5.x.y |
| |
| Next, add the layers to ''bblayers.conf'' |
| <code> |
| BBLAYERS ?= " \ |
| /home/ubuntu/yocto/poky/meta \ |
| /home/ubuntu/yocto/poky/meta-poky \ |
| /home/ubuntu/yocto/poky/meta-yocto-bsp \ |
| \ |
| /home/ubuntu/yocto/meta-openembedded/meta-oe \ |
| /home/ubuntu/yocto/meta-ost/meta-ost \ |
| /home/ubuntu/yocto/meta-ost/meta-ost-toradex \ |
| /home/ubuntu/yocto/meta-toradex-nxp \ |
| /home/ubuntu/yocto/meta-toradex-bsp-common \ |
| /home/ubuntu/yocto/meta-freescale \ |
| /home/ubuntu/yocto/meta-freescale-3rdparty \ |
| " |
| </code> |
| |
| and change the machine definition in ''local.conf'' |
| |
<code> | <code> |
Another change in our device tree is on ''iomux'': some gpios are removed due to conflicts with flexcan and eim. | Another change in our device tree is on ''iomux'': some gpios are removed due to conflicts with flexcan and eim. |
| |
===== Installing Images ===== | |
Use the [[..:toradex:toradex-easy-installer | Toradex Easy Installer]] for our images. | |
| |
| ===== Getting Images ===== |
| Prebuilt images can be obtained from our [[software:linux:images:start|Linux Images]] page. Extract it and flash it onto a SD card or USB stick (see next chapter). |
| |
===== Updating the Bootloader / Recovery Mode ===== | |
| ===== Installing Images ===== |
| Use the [[..:toradex:toradex-easy-installer | Toradex Easy Installer]] to load new images. |
| |
| Updating the bootloader / recovery mode |
* https://developer.toradex.com/knowledge-base/flashing-linux-on-imx6-modules | * https://developer.toradex.com/knowledge-base/flashing-linux-on-imx6-modules |
* https://developer.toradex.com/knowledge-base/imx-recovery-mode#3-colibri-imx6 | * https://developer.toradex.com/knowledge-base/imx-recovery-mode#3-colibri-imx6 |
| |
===== Accessing the Board ===== | ===== Accessing the Board ===== |
To be done | The login shell can be accessed through UART-A. |
| * On the Colibri Evaluation board: use a null modem cable. The communication settings are: 115200 8N1. |
| * On our [[embedded_systems:imx6:cb|Controller Board (cb20)]]: you need a special USB/TTL-Serial-UART converter cable. The connector on the board is a 6-pin SIL connector, e.g. [[http://ch.farnell.com/ftdi/ttl-232r-3v3/kabel-usb-ttl-pegel-seriell-umsetzung/dp/1329311]]. |
| |
| ==== User ==== |
| | user | ost | |
| | pw | ost | |
| The ''root'' user is also available over ssh in development images (such as ''ost-devel'' image). |
| |
| ==== IP-Address ==== |
| | IP | ? | |
| |
| ==== Using WLAN ==== |
| See [[software:linux:toradex:wifi|WiFi on iMX6]] for further information. |
| |
| |