OST » Wikis » Infoportal Sie befinden sich hier: start » software » linux » yocto » x86-rt

Infoportal

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
software:linux:yocto:x86-rt [2023-06-14 15:05] – Urs Grafsoftware:linux:yocto:x86-rt [2023-09-19 15:10] (aktuell) – Urs Graf
Zeile 7: Zeile 7:
  
  
-===== Downloading Images ===== +===== Getting Image ===== 
-Prebuilt images can be obtained from our [[software:linux:images:start|Linux Images]] page.+Prebuilt images can be obtained from our [[software:linux:images:start|Linux Images]] page. Extract it and flash it onto a USB stick.
  
  
-===== Installing Images ===== +===== Booting from the Images =====
-Currently there are only instructions for booting from a USB stick, however, these instructions should serve as a good point of reference for installing on other media (such as SSD's or hard disks). +
- +
-Materials needed: +
- +
-  * USB Stick +
-  * image.wic file (prebuilt or custom) +
-  * x86 based PC with the ability to boot from USB (any reasonably modern PC should be able to do this) +
- +
-==== Identifying the USB Stick ==== +
- +
-Plug in the USB Stick and identify the corresponding block device (''/dev/sdX'') using lsblk. +
- +
-Example output for ''lsblk'': +
-<code> +
-$ lsblk +
-NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT +
-sda           8:0    0   2.7T  0 disk  +
-└─sda1        8:1    0   2.7T  0 part /mnt/hdd +
-sdb           8:16   1   3.8G  0 disk  +
-├─sdb1        8:17   1   681M  0 part  +
-└─sdb2        8:18   1    56M  0 part  +
-sdf           8:80   0   500G  0 disk  +
-sdg           8:96   0   100G  0 disk  +
-├─sdg1        8:97   0   100M  0 part  +
-└─sdg2        8:98   0  99.9G  0 part  +
-nvme1n1     259:0    0 465.8G  0 disk  +
-├─nvme1n1p1 259:2    0   512M  0 part  +
-├─nvme1n1p2 259:3    0 457.3G  0 part  +
-└─nvme1n1p3 259:4    0     8G  0 part  +
-nvme0n1     259:1    0 931.5G  0 disk  +
-├─nvme0n1p1 259:5    0   300M  0 part /efi +
-└─nvme0n1p2 259:6    0 931.2G  0 part / +
-</code> +
- +
-A quick guide to reading the output: +
-''lsblk'' uses a tree to show devices and their partitions. For example ''sda1'' is the first partition on ''sda'' and ''nvme1n1p1'' is the first partition of ''nvme1n1''. +
- +
-''sdX'' where ''X'' is a small letter starting from ''a'' usually represents a SATA or USB drive, names starting with ''nvme'' represent NVME SSDs and SD cards usually start with ''mmcblk''. +
-These names represent the device as found in ''/dev'', so ''sda'' is found under ''/dev/sda''. +
- +
- +
- +
-The easiest way to identify the right block device is usually it's size. +
-In the example output above, we are looking for a 4GB USB Stick. +
-We can infer that the USB Stick is ''/dev/sdb'', since it is the only device with roughly the right size (3.8GB). Note that the size shown in ''lsblk'' may differ slightly from the nominal size of the USB Stick due to partitioning. +
- +
-If there are multiple devices of the same size as the USB stick it may be necessary to run ''lsblk'' before and after plugging in the USB stick and checking which device only appears in the second output. +
- +
-==== Writing the image to the USB stick ==== +
- +
-**WARNING: Writing the image to the USB Stick will erase all content!** +
- +
-**WARNING: Make absolutely sure you have identified the correct device! dd will not hesitate to override your OS drive if you tell it to!** +
- +
-Use the following command to write the image to the USB stick +
-modifying ''/path/to/image.wic'' and ''/dev/sdX'' accordingly. +
-<code> +
-sudo dd if=/path/to/image.wic of=/dev/sdX bs=1M status=progress +
-sudo eject /dev/sdX +
-</code> +
- +
-==== Booting ==== +
 The USB stick can now be used to boot from USB. The USB stick can now be used to boot from USB.
 Note that the BIOS/UEFI setting to achieve this are hardware specific. Note that the BIOS/UEFI setting to achieve this are hardware specific.

Seiten-Werkzeuge

OST - Ostschweizer Fachhochschule - Campus Buchs
Uebersicht
software/linux/yocto/x86-rt.1686747946.txt.gz · Zuletzt geändert: 2023-06-14 15:05 von Urs Graf